If you have a short haircut, it can get very expensive very quickly.It's easy to cut hair with hair clippers.You'll need toFamiliarize yourself with clipper guard numbers to learn the basics of cutting.Then, start cutting your hair based on what you want.Learn how to care for your clippers and follow up with a bit of trimming.
Step 1: There is a numbering system for blade guards.
The length of your hair is determined by the blade guards, which are referred to as the "numbers" in clippers.The shorter the cut, the smaller the number.A "0" will give you barely-there hair, while an8" is 1 inch.The blade guards go up by an eighth of an inch for each number.
Step 2: A good wash is what you should start with.
It is a good idea to wash hair before it's cut to make it easy to comb and not have waves.If the hair tangles, you should use a de-tangler.There is a debate about whether the hair should be wet or dry.It is possible to see what works best for you.
Step 3: The person's shoulders should be covered to catch falling hair.
If you can't shower immediately after getting a haircut, it's a good idea to find a slick material to drape around your shoulders and pull against your neck.A slick fabric allows hair to fall off the floor instead of sticking to clothes.If you want to cut back on the mess, go outside and it won't matter as much.It is possible to cut in the garage.If the weather doesn't permit either of those, stick to an easy-to- clean area, such as the bathroom or kitchen.
Step 4: Start with the longest blade guard.
If you need to remove a lot of hair, start with a blade guard.You can cut parts shorter if you buzz it all over the head.If you need to remove a lot of hair, this method is perfect.If you want #1 on the sides and #2 on top, start buzzing your head with #3.Where you start is up to you.You can either start at the back or move to the other side.If you prefer, you can start at the top.Try not to skip around so you don't miss anything.
Step 5: Move against the growth of hair.
If you think about it, your hair grows down the sides and back.You'll move up the sides and back when you use clippers because you want to go against the growth.You'll move from front to back on the top of your head.
Step 6: The hair should be removed with the blade.
Start by touching the skin with the clippers.Scoop as you come up.Short strokes on your head create a softer cut.
Step 7: The guard should be between the two lengths.
There may be a line between the shorter and longer blade if you've used more than one blade.Use a blade guard between the other blade guards to fade that out.If you've used #2 on the sides and #4 on top, blend with #3.You can smooth out the border by going along the line.
Step 8: Guard 1 can be used for a burr cut.
A burr cut is a cut where you buzz off your hair.Use guard 1 to move around.Proceed to the sides from the back.It's time to buzz off the top.
Step 9: Do a high and tight stance with the guards.
Start by buzzing your whole head.Then shave the sides and back with the guard.Make an even line around your crown by working up from the button.You should go from one side to the other.
Step 10: For a crew cut, begin with a guard 2 or 4.
Start by cutting the sides and back with a blade.You can choose which one you prefer.Leaving the top for last is how to move up to the crown.Slowly reduce the guard size as you cut back to the crown in rows.
Step 11: A basic boy's cut can be created with a shorter guard.
Start by buzzing the whole head with a 3 or 4.If you get the whole head buzzed down, you should change out the blade for a shorter one.You can shorten them by moving up the sides.If you want long hair on top, make sure you keep a clean line around the skull.If you're cutting your own hair, place your hand on top of your head.You don't want to take the clippers too far up your head if you use it to guide them.You can either start in the back or move from one side to the other.
Step 12: Go to a lower number around the ears.
If you want your hair to be the same length, it's a good idea to switch to a lower guard number.That will make you look better.
Step 13: The sideburns and back of the neck should be trimmed.
To get a clean, finished look, you need to even out the sideburns.You move with the growth when trimming.The sideburn should be cut to the desired length.If you want to get them, make sure you look at the person from the front or at yourself in the mirror.To clean up the edges in the back, use the trimmers.
Step 14: Cut around the ears with scissors.
If you have scraggly hairs around the edges of your hair, it can be helpful to trim it with scissors.You might want to trim around the ears with scissors.The scissors are meant for hair cutting.If you're in a pinch, try a small pair of scissors.
Step 15: You can use a lint roller to pick up hair at the end.
A lint roller can be used to get rid of hair.Roll it up and down on the person's neck to get rid of the hairs.
Step 16: Use soap and water to clean the blades.
Remove the hair from the clippers.Use a cloth or light brush to get into the nooks and crevices.They should be left to dry on a towel.
Step 17: Remove hair from the blades and exterior.
Water on the actual clippers is dangerous.If you want to get as much hair off as possible, use a brush.
Step 18: The blades should be oiled.
The blade needs to be turned on.lubricating oil should be added to the blades.It will spread the oil throughout the blades if you let it run for a short time.If you have excess oil, wipe it off with the blades.Most clippers have oil in them.
Step 19: The insides are oiled.
You have to oil the insides of the clippers.Your owner's manual will tell you if your clippers need treatment or not.Some clippers have a spot where you can add a drop of oil, which is indicated by an arrow.