Laundry Error Code FE – What to check – how to clear washer error code FE and washer and dishwasher error codes.

Responsive design allows for a convenient experience that matches your device’s screen size.To get the best experience from our website, please follow the instructions below.

If you’re using Internet Explorer 9 or earlier, you will need to use an alternate browser or upgrade to a newer version of internet Explorer.

A few simple steps can usually resolve an error on the display of the washer.

The washing machine will add a suds reducing cycle if it finds too much suds.The cycle time is increased by 2 hours.The washing machine stops if too many suds are detected.

Do not add more than the manufacturer’s recommended amount of detergent.The amount of detergent should be reduced until there is no more sudsing.You can find more information in our Detergent and Additives usage article.

There is an over-current in the electrical circuit of the motor.It can be caused by a short circuit, loose connection, ground fault or power surge.

Close the water tap if the error code continues.There will be a repair service for the unit.You can request a repair on our page.

When displayed on a multi display, Cd means “cool down” and is an indicator that the drying cycle is completed.

Wrinkle can form when clothes are not removed quickly.The load is fluffed when the cool down feature tumbles to avoid wrinkling.

Until the clothes are removed, the message will continue to display.

There is an indicator that the child lock feature is active.The control panel is disabled when the child lock feature is active.

If the drum is tightly packed, it can force the door out of alignment.

Don’t put weight on the door while it’s open.It is possible to cause a misalignment by putting too much strain on the door hinge.

The sleeves and corners of fabric will not be trapped between the door, glass and gasket if items are placed in the drum completely.

The washer’s door is open and not locked according to the dE1 error code.On your unit’s display, the error may look like dE1, del or dEL.

Close the water taps if the dE1 error code persists.There will be a repair service for the unit.You can request a repair on our page.

Close the water taps if the dE2 error code persists.There will be a repair service for the unit.You can request a repair on our page.

The washer is over filling according to the FE error code.This can be the result of a faulty water valve.

If you want to drain out any trapped water, power the washer back on and press the spin speed button until no spin is selected.

The unit will need a repair service if the FE error code continues.You can request a repair on our page.

The unit will need a repair service if the PE error code continues.You can request a repair on our page.

The code indicates a power failure.If the power supply to the washer is interrupted, this may happen.

Press the power button to plug the washer back in.No spin is highlighted when you press the spin speed button.

Close the water taps if the tE error code persists.There will be a repair service for the unit.You can request a repair on our page.

The child lock option is on if the cycle already started before buttons stopped responding.

Not all options can be selected at the same time.Some models can’t be activated with water plus.

The child lock feature is currently engaged.Before any other buttons other than the power key can work, the control panel must be locked to prevent tampering with a currently running wash cycle.Child Lock can be turned on and off by pressing either the PRE-WASH or TUB CLEAN key.The option button is used on some models.

If the child lock is not engaged and the keys are not working, a repair service may be required.You can request a repair on our page.

Push option buttons will allow you to skip the tub clean cycle.

After a few wash cycles, the reminder message reappears and disappears until the next tub clean cycle.

An unbalanced load and the UE/UE code can be caused by certain load types.

If the drum doesn’t reach 20rpm within 3 minutes or 6 attempts, the error code will be displayed.

A professional technician is needed for the unit.The unit should be unplugged until the repair service is done.You can request a repair by visiting the Request a Repair page.

There is an error code.The child lock feature is set active.The control panel will be disabled when the child lock feature is active.

The D3 error code displays as a result of a malfunctioning part.You can request a repair service on our Request a Repair page.

The washer wasn’t able to lock the drawer.This might be a result of something.

The door latch switch is malfunctioning according to a dL error.There are a number of possible causes that could lead to the display of this code.

If the dL error code continues, the unit will need a repair service.

This isn’t an error.The DR shows that the unit has stopped draining water.

There is an error about the clutch.There is a coin stuck between the pulsator and the tub.

Check the seam between the drum and the pulsator to see if items are stuck there.

The fill error is indicated by the FE error.When the water level gets too high, the code displays.The machine could be filled with water if the inlet valve is faulty.

If you want to get rid of excess water, turn off the water to the unit, perform a drain only or spin only cycle, and then plug it in.

If the FE error code continues, the unit will need a repair service.

An LE error code on the washer’s display indicates that the motor is locked, possibly due to heavy wash load or foreign object such as coins, pins, or clips, caught between the wash plate and the inner basket.

The SPIN SPEED button can be pressed without selecting a cycle to drain the load.

Check pockets before washing to prevent damage to the washer or clothing.

The packing material may not be removed if the unit was installed.

The unit will need a repair service if the LE error code continues.

A professional technician is needed for the unit.The unit should be unplugged until the repair service is done.You can request a repair by visiting the Request a Repair page.

The washing machine will display an error code if it finds too much suds.The cycle time is increased by two hours.The washing machine will stop if too many suds are detected.

Do not add more detergent than the manufacturer’s recommended quantity, and reduce the amount of detergent you use.You can find more information in our Detergent and Additives usage article.

Push option buttons will allow you to skip the tub clean cycle.

After a few wash cycles, the reminder message reappears and disappears until the next tub clean cycle.

The service of a professional technician is required for this error.The unit should not be plugged in until the repair service is complete.You can request a repair by visiting the Request a Repair page.

The dE2 error code can be heard if you hear a noise shortly after starting the cycle.

The height of the drain should not be more than 53″ above the floor.The washer can’t push the water higher.

Before going into the spin cycle, the unit will check each load for balance.The washer will try to adjust the load by adding more water and repeating the rinse cycle if an unbalance load is detected.The wash time may be increased by this.

According to the E7 error code, the stacking switch is malfunctioning or that the SideKick is not installed correctly under the front load washer or dryer.

The tcL code indicates that it is high time to clean the machine.

The washing machine tub cleaners can be used.The amount used for traditional washers should be less because the unit is so small.

The SideKick measuring cup can be used for the correct amount of powdered tub cleaner.Don’t use the entire piece if you are using a tablet.

The unit will need the service of a professional technician if the error code continues.You can request a repair on our page.

The unit will need the service of a professional technician if the error code continues.You can request a repair on our page.

This is normal.The “CD” message displays when the drying cycle is over.There is a prompt for “END OF CYCLE” on the models.”Press any button to load the items” and “unload” will alternate every 3 seconds after that time.

The cool down operation keeps the load cool so it doesn’t get wrinkled for up to 4 hours.

The cool down will continue until the customer presses any of the buttons, or until 4 hours have passed.

Sanmi is the author of a help library article.Please let him know what you think about the page.

We apologize for the time delay.

Get answers to your questions about product setup, use and care.We can help.