What safety glasses shade do you need for the cutting torch?
What safety glasses shade do you need for the cutting torch?
For gas welding and oxygen cutting operations, a Shade 3 up to a Shade 8 is required depending on plate thickness. Lower shades are used for tasks like torch brazing and torch soldering.Jan 29, 2020
What are shade 5 lenses?
Shade levels 2, 3, and 5 are designed for light to medium soldering, brazing, cutting or welding. These lenses do not provide adequate protection for an arc welder (requires shield with shade 8+), but do offer good protection from nearby flash or exposure.
What is shade number?
A shade number indicates the intensity of light radiation that is allowed to pass through a filter lens to one's eyes. Therefore, the higher the shade number, the darker the filter and the less light radiation that will pass through the lens.
Do you need goggles for cutting torch?
The hazard assessment for your welding, brazing, or torchcutting operation should prescribe the combination of filter lenses, headgear, and impact goggles/sidesheilds/glasses that will be necessary for your overall eye/face/head protection from heat, fire, and sparks or other flying objects.
Does a cutting torch hurt your eyes?
So yes the torch can damage the eyes, it just takes longer. Would you rather get burned by 600F molten solder or 2700f molten steel? The worse hazard for your eyes is the "blue hazard". Watching an arc will raise the temperature in your eye to the point of pain but watching the flame will not in the same time frame.Jul 25, 2009
What eye protection is used when operating a cutting torch?
Generally, people who work with torching are either wearing a full face shield with a lens (either an electronic shaded lens or a green glass lens) or they're wearing safety glasses.Oct 11, 2013
Will a plasma cutter burn your eyes?
Don't stare at the bright light! Plasma cutting arcs can also be very intense, because the arc current is typically anywhere from 100 to 800 Amperes. Needless to say, looking at an arc that intense can easily cause eye damage, including permanent damage leading to blindness.
Can you use a cutting torch with sunglasses?
OSHA requires that you use a #3 shade or darker for cutting with an Oxy Fuel torch. Shade 3 would be just medium tinted sunglasses (or a tinted grinding face shield).Jul 25, 2009
Do you need eye protection for acetylene torch?
Oxygen fuel cutting, gas welding and brazing can expose workers to this type of radiation. Exposure to UV and IR raysIR raysIn infrared photography, the film or image sensor used is sensitive to infrared light. The part of the spectrum used is referred to as near-infrared to distinguish it from far-infrared, which is the domain of thermal imaging. Wavelengths used for photography range from about 700 nm to about 900 nm.https://en.wikipedia.org › wiki › Infrared_photographyInfrared photography - Wikipedia can damage the eyes and the skin. ... Protect yourself while using oxy-fuel torches by wearing eye protection that has a welding filter lens designed to protect the eyes from visible, IR and UV rays.
What is the difference between a cutting torch tip and a welding torch tip?
A welding nozzle has a single hole in it where the oxy-acetylene mix exits and burns. ... A cutting torch has the same single hole in the middle of the tip but it has a ring of small holes around it. The surrounding holes are to feed extra oxygen to the flame when you push the oxygen lever on the cutting handle.Jul 17, 2018
What shade goggles should be used with oxy acetylene?
OPERATIONS MINIMUM* PROTECTIVE SHADE
--------------- -------------------------
Gas welding: Heavy
Oxygen cutting: Light
Medium 4
Heavy 5
What eye protection is required when welding with oxy acetylene?
goggles
Do you need goggles for oxy acetylene?
Protect yourself while using oxy-fuel torches by wearing eye protection that has a welding filter lens designed to protect the eyes from visible, IR and UV rays. ... Select goggles or a mask with a tempered shaded lens to protect your eyes from injury and provide good visibility of the work.