Another common issue with ignition is a dirty pilot light orifice, caused by a buildup of soot and dirt. If you have successfully re-lit your pilot light, ensured that the orifice is clean, and the fireplace still refuses to ignite, there could be an issue with the thermopile, thermocouple or wiring.
How do I get my fireplace pilot light back on?
https://www.youtube.com/watch?v=DnZug6GbStY
Why won't my pilot light light on my gas fireplace?
If gas is coming out of the pilot, but it still won't light, the spark igniter could be the problem. Alleyne says to look for and clear out any debris between the igniter and thermocouple. The pilot lighting, but not staying lit, indicates that the thermocouple is worn out, Worthen says.Nov 7, 2014
How do you fix a pilot light on a gasfireplace that won't stay lit?
- Before You Begin: Is Your Pilot Light Lit Inside Fireplace?
- The Fix: Pilot Light to Gas Fireplace Won't Stay Lit.
- Check Your Thermopile Output with the TH/TP Contacts.
- Don't Replace Your Thermopile or Thermocouple Right Away.
- Cleaning the Thermopile.
- Re-test the Cleaned Thermopile.
When I release the pilot button the flame goes out?
1 Answer. Yes, either the thermocouple is going bad, it's not getting heated, or something is wrong with the controller. The most likely of those is that the thermocouple needs to be replaced. The button you press to light the pilot bypasses the thermocouple.
How do you resync a fireplace remote?
https://www.youtube.com/watch?v=rRvO6J9UDAU
How do you reset an electric fireplace?
SOLUTION: Turn all switches to the “off” position and unplug the unit from the wall for five minutes. After five minutes, power everything back on.
Why my electric fireplace is not working?
Make sure that this switch is turned on or your electric fireplace will not produce heat. Your heating element may have burned out. Check electrical wiring and look for any loose connections. Make sure that the wire running to your thermostat is properly attached.Jan 1, 2015
What do I do if my gasfireplace won't light?
If gas is coming out of the pilot but it still won't light, the spark igniter could be the problem. You should clear out any debris between the igniter and thermocouple. Blowing compressed air into the pilot area, waiting a couple minutes, then trying again could help to fix the problem.
Why won't my pilot light ignite on my gas fireplace?
Check the Spark Igniter If gas is coming out of the pilot but it still won't light, the spark igniter could be the problem. You should clear out any debris between the igniter and thermocouple. Blowing compressed air into the pilot area, waiting a couple minutes, then trying again could help to fix the problem.
Why is my electric fireplace blinking E3?
Display shows “E3” Manual Reset overheat protection has triggered. Inspect the heater and check that the air inlets and outlets are not blocked as this may cause overheating. Unplug the heater for 5 minutes and allow it to cool down.
What do you do when your pilot light won't light?
- Find your gas valve.
- You need to turn the valve to the off position for at least three minutes.
- Once you have had the valve at off for a few minutes, switch it over to pilot setting.
- You will need a match that is lit.
- Set the pilot valve to the on position.
When I turn on my gasfireplace the pilot light goes out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don't hesitate to contact a professional.
Why can't I light the pilot light on my gas fireplace?
Check Your Igniter and Thermocouple If nothing is blocking the tubing, and gas is flowing out, there might be something wrong with the spark igniter and thermocouple. Make sure there's no debris lodged between the two. If the pilot light ignites but doesn't stay lit, you might need to replace the igniter.Dec 2, 2019
How do I clean the thermocouple on my gas fireplace?
- Turn off the fireplacegas valve and remove the front panel from the fireplace.
- Find the thermocouple, which is located next to the pilot light and looks like a small straight pipe.
- Use a can of compressed air to gently blow away any dust and dirt from the thermocouple.
Why does my pilot light go out when I release the pilot light knob?
If you're able to light the pilot light, but it goes out when you release the control knob, the thermocouple probably needs replacing. The thermocouple is a safety device that shuts off gas flow if it senses the pilot light is out, but when damaged it loses its regulatory ability.
Why would an electric fireplace stopped working?
When a wire comes loose or the motor stops functioning, the flame will freeze. Check the wiring to make sure that all connections have good contact. Look for exposed and frayed wires. If everything looks good, it's probably time to replace your flame motor.Jan 1, 2015
How do I get my electric fireplace to work?
- Ensure that the fireplace is plugged directly into a wall socket, and that the power switch is turned on.
- Ensure that the main power switch on the electric fireplace is turned on.
- Ensure that the fireplace is plugged in and turned on at the wall.
How do you fix a pilot light that keeps going out?
Once The Flame Is Lit, Turn Gas Control Valve to "On" Once the pilot light is ignited, you can release the reset button after 30 seconds and turn the gas knob to the “On” position. At this time you should hear the main burner come on. Now your pilot light should hold a flame and hot water should be restored!
Why does my electric fireplace have no flame?
The circuit breaker might have tripped, causing the motor flame problem in your unit. The solution to this problem is as easy as flipping it back on. After checking the circuit breaker and fuse, move on to other parts of the electric fireplace. Check if there are any loose connections with the cables.
How do I get my gasfireplace to turn on?
Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it's been since the gasfireplace was last used, ignition may take multiple attempts.
Why does my pilot light keep going out on my gas fireplace?
The Fix: Pilot Light to Gas Fireplace Won't Stay Lit This can be an indication that your fireplace thermocouple is either bad or worn out. However, if your pilot is lit but the gasfireplace isn't, then there's probably a problem with your thermopile.
How do you program a gasfireplace remote?
https://www.youtube.com/watch?v=ax0vVsuZ-bs
How do you clean a gas thermocouple?
The best way to clean your thermocouple is to use either a piece of steel wool or the coarse side of a sponge to gently clean off any soot or other remnants. You can use a pencil eraser to clean between the threads of the screw that connects the thermocouple to the control valve of your system.